tinySA Ultra+ 100 kHz – 7.3 GHz Portable Spectrum Analyzer ZS-407

Description

The tinySA Ultra+ portable spectrum analyzer features a 4,0-inch resistive touchscreen color display that displays the full frequency range at 450 scan points, and comes with a rechargeable battery that provides up to two hours of operation in portable mode. In addition, the analyzer has two different modes: normal mode and ultra mode. The tinySA Ultra+ has a variety of built-in setup options, such as a switchable bandpass filter and a step input attenuator. It is important to remember that the maximum input level of the tinySA is +6 dBm. If you are unsure of the input signal level, it is recommended to use an attenuator.

When not being used as a spectrum analyzer, the tinySA Ultra+ can also be used as a sine or square wave generator.

The analyzer can be fully controlled from a PC via a USB cable. It also features automatic self-diagnosis and auto-calibration using a built-in signal generator.

Comparison

TinySA Ultra (ZS405) and TinySA Ultra+ (ZS407) are both portable spectrum analyzers, but the Ultra+ has a more advanced specification. The TinySA Ultra+ supports a wider frequency range: 0,1-900 MHz (0,1-800 MHz for the basic TinySA Ultra model) and up to 7,3 GHz in Ultra mode (5,3 GHz for the TinySA Ultra). In addition, the TinySA Ultra+ also has higher signal generation limits: up to 6,3 GHz for square waves and 7,3 GHz for test signals, in contrast to the TinySA Ultra's performance: 4,4 GHz and 5,3 GHz, respectively. Both models have a 4-inch color screen with a resolution of 450 dots, a microSD card slot and memory for storing measurement results and settings. The improved TinySA Ultra+ model is ideal for more demanding tasks and professional use.

TinySA Ultra+ analyzer specifications

• Frequency range of the analyzer:
  – from 100 kHz to 900 MHz (in normal mode)
  – from 100 kHz to 7.3 GHz (in Ultra mode)
  – calibrated for signal levels up to 7.3 GHz
  – capable of observing signals up to 12 GHz
• Input impedance: 50 ohms (with input attenuator > 10 dB)
• Compression point at 1 dB: -1 dBm (at 0 dB internal attenuator)
• Phase noise: -100 dB/Hz for 10 kHz offset and -103 dB/Hz for 100 kHz offset
• Manual or automatic input attenuator, switchable from 0dB to 31dB in 1dB increments (with LNA off)
• Maximum permissible input signal level: +6 dBm at 0 dB input attenuator
• The maximum permissible short-term peak level of short input signals: +20 dBm, with an input attenuator of 30 dB
• Recommended input signal level in automatic input attenuator mode: +0 dBm
• For best measurement results, keep the input signal level <-25 dBm
• Maximum input voltage: ±5 V DC
• Dynamic range: 70 dB (no spurious harmonics at RBW 30 kHz)
• Power measurement resolution: 0,5 dB
• Frequency uniformity: ±2 dB to 5,3 GHz, ±5 dB from 5,3 GHz to 6 GHz
• Absolute power level measurement error: ± 2 dB (after calibration)
• Intersection point of the third-order modulation products (IIP3) at the input: +15 dBm, with an internal attenuator of 0 dB
• Bandwidth of resolution filters: 0.2, 1, 3, 10, 30, 100, 300, 600 and 850 kHz
• Scanning speed: more than 1000 pixels/sec, when using filters with the largest bandwidth
• Resolution: 51, 101, 145, 290 or 450 measurement points
• Automatic optimization of the actual scan points to ensure coverage of the entire scan range regardless of the selected resolution filter
• Suppression of spurious interference to differentiate between marks from internally generated harmonics and the real input signal
• Built-in 20 dB LNA with a noise factor of 5 dB
• Displayed Average Noise Level (DANL)
• Lowest noticeable signal level without LNA at 30 MHz frequency and 30 kHz resolution band: -102 dBm
• The smallest noticeable signal level from LNA at a frequency of 30 MHz and a resolution band of 200 Hz: -145 dBm

Characteristics of the signal generator

• Frequency range:
  – sinusoidal output: 100 kHz – 900 MHz
  – Square wave output: up to 6.3 GHz when not used as a spectrum analyzer
• Harmonics: < -40 dBn in the range of 100 kHz - 900 MHz
• Modulation: AM, UP-FM, SH-FM
• Level Accuracy: ±2dB to 900MHz for levels between -72dBm and -18dBm, derating below -72dBm.
• Frequency resolution: 44 Hz (up to 900 MHz)

Інтерфейс користувача

• Screen: touch, resistive
• 16 bits per RGB pixel
• Jog switch control
• Management via USB port
• Linear power supply to avoid impulse interference

Complete set

The tinySA Ultra+ analyzer package includes:

• 1 x SMA antenna
• 1 x SMA male to female adapter
• 2 x ALSR100 30cm cable with SMA connectors
• 1 x USB-C cable
• 1 x 32GB microSD card